The agglomeration process in which lumps are made by compacting the iron bearing fines and dust with addition of binder and also deairing these mixtures inside the vacuum chamber of the briquetting machine. So, briquetting process is developed to meet these demands. This process aims at recycle and reuse of the low grade iron ore and plant fines.
A sketch of the Midrex process with a roller press for hot briquetting and without an attached EAF and a detailed description is provided in Lohmeier et al. Not all the iron that is supplied as iron ore to the Midrex plant leaves it as HBI. Ironcontaining material is removed from the process at several sites.
This paper describes an attempt to utilize iron ore slime in basic oxygen steelmaking as a coolant (instead of lump iron ore). Prior to its use, it is briquetted for ease of charging. The tests are carried out in a regular, commercial basic oxygen steelmaking furnace (160 ton/batch, and duration about 45 min).
Pan et al. [9] recommended a prebriquetting process where the specular iron ore were briquetted in presence of lime and chemical binder prior to mixing with other sinter mix ingredients. They ...
Introduction Iron ore fines (size less than 6 mm) are created as a result of mining, crushing and processing large ore particles and they may stand for up to 50% of the total ore mined [1]. Iron ore fines need to be enlarged for better handling and transportation but also for increased permeability in the blast furnace.
The Midrex process produces metallurgical residues in the form of dust, sludge, and fines. As these have high iron content, herein, the aim is to recycle the residues and use them as an educt in the Midrex process, thus closing the material cycle and increasing raw material efficiency. Briquetting of these
approximately % of the total iron [2]. These fines cannot be directly charged back into the BF or steelmaking unit without conducting proper sorting, mixing, and agglomeration processes. Agglomeration via sintering and briquetting processes plays a vital role in the internal recycling of byproducts to recover iron, carbon, and lime.
Iron ore powder agglomeration is the basis for blast furnace ironmaking and is the processing work in between ore crushing, ore grinding separation, and steelmaking. Its purpose is to provide highquality furnace burden for steelmaking. It is an important process of modern iron and steel complex. Iron ore powder agglomeration processes include ...
The briquetting process is the conversion of agricultural waste into uniformly shaped briquettes that are easy to use, transport, and store. The idea of briquetting is using materials that are unusable, due to a lack of density, and compressing them into a solid fuel of a convenient shape that can be burned like wood or charcoal. The briquettes ...
Abstract. Briquette binder plays a key role in the process of briquette production. The quality and performance of briquette also depend on the quality of briquette binder. Different types of ...
Abstract. This review presents the usage of adhesives and binders for agglomeration of particle materials, including waste, in order to obtain strong bodies. The binding materials were classifi ed ...
when designing the briquetting process. For example, it is necessary to take into account the change in yield during briquette transportation after briquetting. These dependences are also necessary for formulating and solving problems of pressing/briquetting of finely dispersed materials, including iron ore concentrate with coke screenings.
DRI fines, generated during its manufacture and handling, generate high content of fines in the size fraction less than 2 mm. It has iron content above 80%. It is difficult to directly use such ironrich material in the primary steel making process, without agglomeration. At JSW Steel Vijayanagar, around 50 to 70 tons per day of DRI fines with < 2 mm size fraction get generated. The fines are ...
PDF Size: Mb. Unique ID: p
This work proposes a novel horizontal highshear granulator for iron ore granulation before sintering process. The granulation behavior such as growth process and structure of granules were firstly analyzed, followed by the effects of operation conditions such as water content, initial particle size distribution, and the concentrate ratio. The results show that the granule size increased ...
The current state of briquetting technology in iron smelting processes is assessed. For the first time, the importance of using orecoal briquettes for the charge in blast furnace processes as a means of reducing the total carbon consumption and emissions of CO2 is shown. The role of solidstate reduction in blastfurnace orecoal briquettes in improving the rate of utilization of the reducing ...
A traditional application for briquetting is the agglomeration of coal. Most applications of briquetting in the iron and steel industry involve waste materials, such as mill scale and process dusts, sludges, and filter cakes [27]. In the DR industry, a number of facilities briquette their hot DRI product to produce a higherdensity product for ...
Abstract. Briquetting is a continuous compaction process to transform loose powders into solid briquettes. The density and strength of formed briquettes vary significantly in the process, affecting the quality of products. This work presented a numerical modelling of briquetting based on Finite Element Method (FEM), focusing on the evolutions ...
Iron ore handling, which may account for 2050% of the total delivered cost of raw materials, covers the processes of transportation, storage, feeding, and washing of the ore en route to or during its various stages of treatment in the mill.. Since the physical state of iron ores in situ may range from friable, or even sandy materials, to monolithic deposits with hardness of granite, the ...
A kind of leaching residue generated during high pressure acid leaching of laterite nickel ore is creatively prepared as blast furnace charge for ironmaking. Results show that the briquettes with uniform shape, compressive strength higher than N/pellet, and cracking temperature over 400 °C can be obtained by the nonbinder briquetting with water content of wt.% and pressure of 30 ...
DRI fines, generated during its manufacture and handling, generate high content of fines in the size fraction less than 2 mm. It has iron content above 80%. It is difficult to directly use such ironrich material in the primary steel making process, without agglomeration. At JSW Steel Vijayanagar, around 50 to 70 tons per day of DRI fines with < 2 mm size fraction get generated. The fines are ...
© DZCrusher - كل الحقوق محفوظة
